UniMatchTM deep wedge V-belts

Oil and heat-resistant.
Static dissipating.

A more narrow, deeper wedge shape with more efficient load
carrying characteristics and higher power capability allows for smaller,
more compact drives. These belts feature the UniMatch construction.
This eliminates belt set matching with its multiple stocking and belt
wastage problems.

These belts conform to RMA Engineering Standard IP-22.

Stock UniMatch deep wedge V-belts are listed below. In-
between lengths and lengths over 600 inches are available on special
order.

Deep wedge V-belts are identified by a number
and letter specifying the belt section and a number
giving the outside length in inches multiplied by 10.
For example: 3V1250.

3V Section Deep Wedge V-Belts (3/8-inch Top Width, 5/16-inch Thick)

5V Section Deep Wedge V-Belts (5/8-inch Top Width, 17/32-inch Thick)

8V Section Deep Wedge V-Belts (1-inch Top Width, 7/8-inch Thick)

3V2503V6305V5005V14008V10008V2500
3V2653V6705V5305V15008V10608V2650
3V2803V7105V5605V16008V11208V2800
3V3003V7505V6005V17008V11808V3000
3V3153V8005V6305V18008V12508V3150
3V3353V8305V6705V19008V13208V3350
3V3553V8505V7105V20008V14008V3550Double multiple V-belts
3V3753V9005V7505V21208V15008V3750
8V8008V2240
3V4003V9508V16008V4000
3V4253V10005V8505V23608V17008V4250
3V4503V10605V9005V25008V18008V4500
3V4753V11205V9505V26508V19008V4750
3V5003V11805V10005V28008V20008V5000
5V10605V3000
3V5303V12508V21208V5600
3V5603V13205V11205V31508V2240
3V6003V14005V11805V33508V2360
5V12505V3550
5V1320

AA Section Double Multiple V-Belts (1/2-inch Wide, 13/32-inch Thick)

BB Section Double Multiple V-Belts (21/32-inch Wide, 17/32-inch Thick)

CC Section Double Multiple V-Belts (7/8-inch Wide, 11/16-inch Thick)

DD Section Double Multiple V-Belts (1-1/4-inch Wide, 1-inch Thick)

AA51BB43BB103BB240CC162DD210
*AA55*BB45BB105BB255CC173DD240
*AA58*BB51BB107BB270CC180DD270
*AA60*BB55BB111BB278CC195
BB60BB112BB300CC210DD300
AA68DD330
AA73BB62BB120CC75CC240DD360
*AA75BB68BB124CC81

Especially designed for serpentine and reversing drives, double
V-belts transmit power from both sides of the belt. Polyester cords
and cotton/polyester cover provide maximum strength and length
stability with minimum stretch. These belts conform to RMA
Engineering Standard IP-21.

Double V-belts are available in four standard RMA sections AA,
BB, CC and DD and in lengths to 540 inches. They are specified by
belt section letters, inside length in inches. DD sections are for
replacement only and are not recommended for new drives.

AA80BB74BB128CC85CC270DD390
BB75BB130CC90CC300DD420
AA85BB76BB136CC96CC330DD480
AA90CC360
AA96BB85BB173CC105CC390DD540
AA105BB90BB180
BB93BB195CC112CC420
AA112BB94BB210CC119
AA120BB96BB228CC120
AA128BB97CC128
CC144
CC158


Revised: 21 Sep 97
Copyright © 1997 St. Louis Factory Supply Inc.
bobstlfs@juno.com

24-HOUR SERVICE 1-866-234-2358


[Toll Free] 1-866-234-2358
[Phone] (314) 842-6969
[FAX] (314) 842-1526

[Back] [Home] [Next]